Furuno class b ais transponder serial#
Furuno class b ais transponder update#
Furuno class b ais transponder manual#
Furuno class b ais transponder Pc#

(Time, Pos, SOG, COG, Heading, Nav status, etc) (Ship name, MMSI, Callsign, Type of Vessel, etc) IP ADR SUB NET MASK PORT NO POWER CHANNEL NO.

Furuno class b ais transponder Pc#

Setting PC I/O SNSR1 SNSR2 SNSR3 LR BEACON EXTRA1 XTRA I/O PORT LR 1.L/L COG SOG 2.HDG 3.ROT AIS Initial Setting List (FA-100) Setting Item This Test Report is in accordance with MSC.1/Circ. The AIS has been tested according to IMO SN/Circ.227 and resolution MSC.74(69), annex 3 Name of Radio Inspector Date and place Name of Radio Inspector Company performance test 6.1 Check reception performance 6.2 Confirm reception of own signal from other ship/VTS 6.3 Polling by VTS/shore installation Electromagnetic interference from AIS observed to other installations?: 70 5.4 Read data from AIS 5.5 Send data to AIS 5.6 Check AIS response to virtual vessels. Performance test using measuring instrument 5.1 Frequency measurements AIS ch. voyage related information 4.1 Ships draught 4.2 Type of cargo 4.3 Destination and ETA (at masters discretion) 4.4 Route plan (optional) 4.5 Short safety-related messagesДҐ. Dynamic information 3.1 Ships position with accuracy and integrity status (Source: GNSS) 3.2 Time in UTC (Source: GNSS) 3.3 Course over ground (COG) (will fluctuate at dockside) (Source GNSS) 3.4 Speed over ground (SOG) (zero at dockside) (Source: GNSS) 3.5 Heading (Source: Gyro) 3.6 Navigational status 3.7 Rate of turn, where available (ROT) 3.8 Angle of heel, pitch and roll, where available 4. Static information 2.1 MMSI number 2.2 IMO number 2.3 Radio call sign 2.4 Name of ship 2.5 Type of ship 2.6 Ship length and beam 2.7 Location of GPS antenna 3. Installation details Item AIS transponder type: 1.1 Type approval certificate 1.2 Initial installation configuration report on board? 1.3 Drawings provided? (Antenna-, AIS-arrangement and block diagram) 1.4 Main source of electrical power, 1.5 Emergency source of electrical power, 1.6 Capacity to be verified if the AIS is connected to a battery 1.7 Pilot plug near pilots operating position? 1.8 120 V AC provided near pilot plug? (Panama and St. Antenna Lay outДЄUTO MATIC IDENTIFICATION SYSTEM (AIS) TEST REPORT Name of ship/call sign: MMSI number: Port of registry: IMO Number: Gross tonnage: Date keel laid:ДЎ. The AIS has been tested according to IMO SN/Circ.227 and resolution MSC.74(69), annex 3Д¬ontents AUTO MATIC IDENTIFICATION SYSTEM (AIS) TEST REPORT Attachments 1.

Furuno class b ais transponder serial#

4 SET LAN PORT menu for PC connectionДЄIS Test Report Model: FA-150 FA-100 Serial Number: Name of ship: 2/2 GATEWAY ADDRESS 000.000.000.000 HOST NAME: AIS0 AIS0OUTPUT: CONTINUOUS GPSOUTPUT: AUTO ZDAOUTPUT: AUTOДЇig.3 SET LAN PORT (2/2) for NavNet connectionДЇig.4 shows the original menu for PC connection. Items in bold are setup on each FA-150 and other items remain unchanged. SET LAN PORT menu Figs.2 and 3 show SET LAN PORT menu for NavNet connection with #4 of S3 set to OFF position. Remarks Not used For PC connection For NavNet vx2 and 3D connection

Furuno class b ais transponder update#

*00015767500* *00015767500* * 0 0 0 1 5 7 6 7 5 0 0 *Д¬onnection to NavNet vx2 and 3D To connect FA-150 to NavNet vx2 and 3D via LAN, software update and change of DIP switch setting are required. гѓ»FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax

Furuno class b ais transponder manual#

The paper used in this manual is elemental chlorine free. Under no circumstances should the contents of this manual be released to the user. Important This manual is intended for use by authorized FURUNO service technicians for the installation of this equipment. System Setting Note: Special characters: $ *, ! ^ ~ INLAND AIS FA-1501: Ver.02.02 or more/FA-1502: Ver.02.01 or more (For INLAND AIS and ITU-R M 1371-3 specifications) Chapter 3.